Basler-electric BE1-851E DNP3 Protocol Instrukcja Użytkownika Strona 1

INSTRUCTION MANUAL FOR ENHANCED OVERCURRENT PROTECTION SYSTEM BE1-851E DISTRIBUTED NETWORK PROTOCOL (DNP3) Publication: 9289900792 Revision: C

1-2 BE1-851E DNP Protocol 9289900792 Rev C

SECTION 2 • DEVICE PROFILE DOCUMENT Introduction Table 2-1 provides a Device Profile Document in the standard format defined in the DNP3 subset defi

DEVICE PROFILE DOCUMENT Timeouts while waiting for: Data Link Confirm None Fixed at 3000 ms Variable Configurable Complete Appl. Fragm

SECTION 3 • IMPLEMENTATION TABLE DNP Implementation Table Table 3-1 identifies which object variations, function codes, and qualifiers the BE1-851E DN

OBJECT REQUEST (BE1-851E will parse) RESPONSE (BE1-851E will respond with) Object No. Variation No. Description Function Codes (dec) Qualifier Codes (

Notes for Table 3-1: 1. A Default variation refers to the variation responded to when variation 0 is requested and/or in class 0, 1, 2, or 3 scans.

3-4 BE1-851E DNP Protocol 9289900792 Rev C

SECTION 4 • CONFIGURATION PARAMETERS DNP Configuration Parameters These paragraphs describe configuration settings that may be verified/changed from t

4-2 BE1-851E DNP Protocol 9289900792 Rev C

SECTION 5 • POINT LIST TABLE OF CONTENTS SECTION 5 • POINT LIST ...

ii BE1-851E DNP Protocol 9289900792 Rev C

SECTION 5 • POINT LIST Binary Input Points Binary Input changes are scanned every four milliseconds. Events are pending in the Slave application buff

Point Index Description Change Event Assigned Class (1,2,3 or none) Notes 26 79 Sequence Control Block 1 27 Input Contact 1 1 28 Input Contact 2 1

Point Index Description Change Event Assigned Class (1,2,3 or none) Notes 63 Clock Error Alarm 1 64 MPU Reset Alarm 1 65 Settings Changed 1 66 E

Binary Output Status Points and Control Relay Output Jacks Table 5-2 lists both the Binary Output Status Points (Object 10) and the Control Relay Ou

Point Index Description Control Codes And Their Description 26 Local Setting Group Control Switch Latch On: Return Setting Group Control to relay lo

Appendix for Binary Output Status Points and Control Relay Output Blocks To enable Master which can support only Trip and Close commands to control BE

Point Index Description Complementary (C) or Single (S) Function Index Permitted Codes 9 Hardware Output A Local Control S 0x03(Latch On/NUL) or 0x41

Point Index Description Complementary (C) or Single (S) Function Index Permitted Codes 33 Hardware Output 5 - Pulse Control 34 Hardware Output 6 - Pul

Index Description Change Event Assigned Class (1, 2, 3, or none) Notes 117 3I0 Current Magnitude 2 1, 1∗ 5 Present Demand Current - Phase A 2 1, 1∗ 6

INTRODUCTION This instruction manual provides detailed information about the BE1-851E Enhanced Overcurrent Protection System with the Distributed Net

Index Description Change Event Assigned Class (1, 2, 3, or none) Notes 41 5th character of Active Logic Name 3 16 42 6th character of Active Logic Na

Index Description Change Event Assigned Class (1, 2, 3, or none) Notes 76 Phase B Time Stamp - part 1; days none 11 77 Phase B Time Stamp - part 2; m

Index Description Change Event Assigned Class (1, 2, 3, or none) Notes 114 Negative Sequence none 1 115 Negative Sequence Time Stamp - part 1; days n

Value/Bit Mask Part 1 Description Part 2 Description 0200h 150TB 151B 0400h 150TC 151C 0800h 150TN 151N 1000h 150TQ 151Q 2000h spare spare 4000h spare

15. BF status is the bit mapped variable with format as described in Table 5-7. Delta of 1 deviation will cause en event. Table 5-7. Breaker Failure

Table 5-9. Analog Output Status Points and Control Blocks Analog Output Status Points Object Number: 40 Variations Supported: 1, 2 Request Function Co

request, with FC= 5 or 6, specific Binary Output Status points can not be first Enabled via its Mode point of object 41, and immediately after that c

Table 5-11. Relay Trouble Status Format Bit Mask (hex) Name Bit Mask (hex) Name 0001 (spare) Reserved for RAM FAILURE 0040 (spare) Reserved for PWR SU

8-Bit Unsigned Integer, Object 102 Table 5-12 is the point list for Object 102, and lists the 8-Bit Unsigned Integer Points. Note that this object has

First Printing: April 2006 Printed in USA © 2006-2013 Basler Electric, Highland Illinois 62249 USA All Rights Reserved October 2013 CONFIDENTIAL

12570 State Route 143 Highland IL 62249-1074 USA Tel: +1 618.654.2341 Fax: +1 618.654.2351 email: [email protected] P.A.E. Les Pins 67319 Wasselonne

REVISION HISTORY The following information provides a historical summary of the changes made to this instruction manual (9289900792). Revisions are li

iv BE1-851E DNP 9289900792 Rev C

CONTENTS SECTION 1 • GENERAL INFORMATION ... 1-1 SECTION

vi BE1-851E DNP 9289900792 Rev C

SECTION 1 • GENERAL INFORMATION Introduction This document describes the Basler Electric Distributed Network Protocol (DNP) implementation in the BE1-